hy_vfd − HAL userspace component for Huanyang VFDs
hy_vfd [OPTIONS]
This component connects the Huanyang VFD to the LinuxCNC HAL via a serial (RS-485) connection.
The Huanyang
VFD must be configured via the face plate user interface to
accept serial communications:
PD001 = 2
Set register PD001 (source of run commands) to 2 (communication port).
PD002 = 2
Set register PD002 (source of operating frequency) to 2 (communication port).
|
PD004 |
Set register PD004 (Base Frequency) according to motor specs. This is the rated frequency of the motor from the motor’s name plate, in Hz. | ||
|
PD005 |
Set register PD005 (max frequency) according to motor specs. This is the maximum frequency of the motor’s power supply, in Hz. | ||
|
PD011 |
Set register PD011 (min frequency) according to motor specs. This is the minimum frequency of the motor’s power supply, in Hz. | ||
|
PD141 |
Set register PD141 (rated motor voltage) according to motor name plate. This is the motor’s maximum voltage, in Volts. | ||
|
PD142 |
Set register PD142 (rated motor current) according to motor name plate. This is the motor’s maximum current, in Amps. | ||
|
PD143 |
Set register PD143 (Number of Motor Poles) according to motor name plate. | ||
|
PD144 |
Set register PD144 (rated motor revolutions) according to motor name plate. This is the motor’s speed in RPM at 50 Hz. Note: This is not the motor’s max speed (unless the max motor frequency happens to be 50 Hz)! |
PD163 = 1
Set register PD163 (communication address) to 1. This matches the default in the hy_vfd driver, change this if your setup has special needs.
PD164 = 2
Set register PD164 (baud rate) to 2 (19200 bps). This matches the default in the hy_vfd driver, change this if your setup has special needs.
PD165 = 3
Set register PD165 (communication data method) to 3 (8n1 RTU). This matches the default in the hy_vfd driver, change this if your setup has special needs. Note that the hy_vfd driver only supports RTU communication, not ASCII.
Consult the Huanyang instruction manual for details on using the face plate to program the VFDs registers, and alternative values for the above registers.
−d, −−device <path>
(default /dev/ttyS0) Set the name of the serial device node to use.
−g, −−debug
Turn on debug messages. Note that if there are serial errors, this may become annoying. Debug mode will cause all serial communication messages to be printed in hex on the terminal.
−n, −−name <string>
(default hy_vfd) Set the name of the HAL module. The HAL comp name will be set to <string>, and all pin and parameter names will begin with <string>.
−b, −−bits <n>
(default 8) Set number of data bits to <n>, where n must be from 5 to 8 inclusive. This must match the setting in register PD165 of the Huanyang VFD.
−p, −−parity [even,odd,none]
(default odd) Set serial parity to even, odd, or none. This must match the setting in register PD165 of the Huanyang VFD.
−r, −−rate <n>
(default 38400) Set baud rate to <n>. It is an error if the rate is not one of the following: 110, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. This must match the setting in register PD164 of the Huanyang VFD.
−s, −−stopbits [1,2]
(default 1) Set serial stop bits to 1 or 2. This must match the setting in register PD165 of the HuanyangVFD.
−t, −−target <n>
(default 1) Set HYCOMM target (slave) number. This must match the device number you set on the Hyanyang VFD in register PD163.
−F, −−max−frequency <n>
(default: read from VFD) If specified, program register PD005 of the VFD with the specified max frequency of <n> Hz (and use the same max frequency in the hy_vfd driver). If not specified, read the max frequency to use from register PD005 of the VFD.
−f, −−min−frequency <n>
(default: read from VFD) If specified, program register PD011 of the VFD with the specified minimum frequency of <n> Hz (and use the same minimum frequency in the hy_vfd driver). If not specified, read the minimum frequency to use from register PD011 of the VFD.
−V, −−motor−voltage <n>
(default: read from VFD) If specified, program register PD141 of the VFD with the specified max motor voltage of <n> Volts. If not specified, read the max motor voltage from register PD141 of the VFD.
−I, −−motor−current <n>
(default: read from VFD) If specified, program register PD142 of the VFD with the specified max motor current of <n> Amps. If not specified, read the max motor current from register PD142 of the VFD.
−S, −−motor−speed <n>
(default: compute from value read from VFD P144) This command-line argument is the motor’s max speed. If specified, compute the motor’s speed at 50 Hz from this argument and from the motor’s max frequency (from the −−max−frequency argument or from P011 if −−max−frequency is not specified) and program register PD144 of the VFD. If not specified, read the motor’s speed at 50 Hz from register P144 of the VFD, and use that and the max frequency to compute the motor’s max speed.
−P, −−motor−poles <n>
(default: read value from VFD P143) This command-line argument is the number of poles in the motor. If specified, this value is sent to the VFD’s register PD143. If not specified, the value is read from PD143 and reported on the corresponding HAL pin.
<name>.enable
(bit, in) Enable communication from the hy_vfd driver to the VFD.
<name>.SetF
(float, out)
<name>.OutF
(float, out)
<name>.OutA
(float, out)
<name>.Rott
(float, out)
<name>.DCV
(float, out)
<name>.ACV
(float, out)
<name>.Cont
(float, out)
<name>.Tmp
(float, out)
<name>.spindle−forward
(bit, in)
<name>.spindle−reverse
(bin, in)
<name>.spindle−on
(bin, in)
<name>.CNTR
(float, out)
<name>.CNST
(float, out)
<name>.CNST−run
(bit, out)
<name>.CNST−jog
(bit, out)
<name>.CNST−command−rf
(bit, out)
<name>.CNST−running
(bit, out)
<name>.CNST−jogging
(bit, out)
<name>.CNST−running−rf
(bit, out)
<name>.CNST−bracking
(bit, out)
<name>.CNST−track−start
(bit, out)
<name>.speed−command
(float, in)
<name>.spindle−speed−fb
(float, out) Current spindle speed as reported by Huanyang VFD.
<name>.spindle−at−speed−tolerance
(float, in) Spindle speed error tolerance. If the actual spindle speed is within .spindle−at−speed−tolerance of the commanded speed, then the .spindle−at−speed pin will go True. The default .spindle−at−speed−tolerance is 0.02, which means the actual speed must be within 2% of the commanded spindle speed.
<name>.spindle−at−speed
(bit, out) True when the current spindle speed is within .spindle−at−speed−tolerance of the commanded speed.
<name>.frequency−command
(float, out)
<name>.max−freq
(float, out)
<name>.base−freq
(float, out)
<name>.freq−lower−limit
(float, out)
<name>.rated−motor−voltage
(float, out)
<name>.rated−motor−current
(float, out)
<name>.rated−motor−rev
(float, out)
<name>.motor−poles
(u32, out)
<name>.hycomm−ok
(bit, out)
<name>.error−count
(s32, RW)
<name>.retval
(float, RW)
Sebastian Kuzminsky
GPL